模块特点
PLCcore Firmware: |
IEC61131-3 |
PLCcore-iMX35 CODESYS: |
IEC61131-3 runtime kernel pre-installed, Shared process image, CiA302/314 compliant CANopen manager, Program download via Ethernet |
PLCcore-iMX35 CODESYS HMI: |
IEC61131-3 runtime kernel pre-installed, Shared process image, CiA302/314 compliant CANopen manager, Program download via Ethernet |
Controller: |
Freescale i.MX357 with ARM11 Core |
System Clock: |
532 MHz |
RAM: |
128MiB DDR2-SDRAM |
FLASH: |
128MiB NOR |
On-board Peripherals: |
DMA, MMU, hardware watchdog, temperature sensor, RTC |
Fast Ethernet: |
1x 10/100Mbps, on-board PHY |
CAN: |
2 |
UART: |
3 |
USB: |
1x USB 2.0, 12Mbps full-speed
1x OTG |
SPI/I2C: |
1/1 |
Mass storage: |
MMC/SD-card signals on board-to-board connector |
LCD: |
TFT-LCD interface brought out via CMOS , resolution 800x600 max. 24bit |
Others: |
S/PDIF |
Operating Conditions: |
Temperature: -40°C…+85°C
Humidity: 10-90% RH, non-condensing |
Power Supply: |
3.3V +/- 5%, 0.3A max. |
Dimensions/Weight: |
78 x 54 x 7,2 (L x W x H in mm), 20g |
Board-to-board connector: |
2x 2x 50 pin header socket, 1.27 mm pitch |
Available on board-to-board connector: |
2x CAN, 3x ASC, 2x USB, I²C, SPI, 2x SD-card, 18x GPIO, Ethernet, TFT-CMOS, PWM/DIO, Timer/Counter/DIO |
RoHS compliant: |
yes |
Operating System: |
Linux, Qt framework necessary for HMI |
Integrated Development Environment (IDE): |
CODESYS V3.5 SP4 Patch4 |
|
|
说明
The PLCcore-iMX35 CODESYS is an IEC 61131-3-programmable Soft-PLC with integrated target visualization. That's why it represents itself as the ideal base component for designing user specific HMI devices. The PLCcore-iMX35 CODESYS provides 16 digital inputs and 10 digital outputs for direct connection to local peripherals. Due to the various communication interfaces such as Ethernet, CAN and serial interfaces, furthermore remote extension equipment can be connected. The PLC Runtime System supports data exchange by several CODESYS libraries for CANopen, CAN Layer 2 and serial COM interfaces.
The PLCcore-iMX35 CODESYS allows for direct connection of CMOS and LVDS displays. The integrated target visualization is based on the CODESYS-internal Visualization Manager, which uses Qt components. It supports a touchscreen, a USB mouse as well a USB keyboard as input devices. The necessary Qt components for the visualization are provided by the Linux BSP and are available to the PLC Runtime System. A separate installation of the Qt components as handled in former systems (e.g. PLCcore-9263 CODESYS) is no longer necessary.
Only a minimal peripheral wiring is necessary to apply the PLCcore-iMX35 CODESYS on an application-specific baseboard. That's why devices based on this core module can be designed very cost-efficiently.
Additional arbitrary Linux applications can be executed on the PLCcore-iMX35 CODESYS in parallel to the PLC Runtime System. For data exchange between a Linux application and the PLC Runtime System, inter process communication mechanisms such as FIFOs or Shared Memory are available. Furthermore, the PLC has full access to the file system. On demand, data can be written to or read from any mounted media.
The PLCcore-iMX35 CODESYS is equipped with an on-board Flash of 128 MiB, whereby a memory range of 90 MiB is freely available as mass storage for the PLC program, for visualization data and for process data. Due to the usage of UBIFS (Unsorted Block Image File System) with active journaling, the file system keeps in a consistent state even in case of an unexpected power supply crash.
The PLC Runtime System allows for usage of one CAN interface as CANopen-Manager. A CAN Layer 2 communication can be performed over both CAN interfaces. The therefor necessary function blocks and functions are implemented in the CODESYS-internal libraries. The integrated CAN controllers are equipped with a receive FIFO. That's why even applications with permanent CAN bus load up to 70 percent can be implemented without any packet loss of CAN messages. |